News from October 2024

Our News

We fitted the replacement ‘chip’ provided by MJ-Hobby to our T23, and after some tweaking here and there we got the locomotive to work as it should, with good slow-speed control. Unfortunately, having removed the main circuit board during our earlier investigation, the wafer-thin ribbon cable to the lights at the B-end snapped (quite undramatically) and thus, we have no lights at that end now. Hopefully, Jeco can supply a replacement (it is a plugin part). Curiously, the chip is marked LP5, which one of our Friends identified as Loco-Pilot 5, a DCC accessory; but aside from the need to run-in, the loco does seem to be OK on analogue with this chip.

The Dekas Y2K in analogue form, has the same problem as the T23! One has arrived here and we are in dialogue with our supplier about getting this problem fixed; hopefully it just needs a replacement ‘chip.’ As we understand it, the model has been supplied with a DCC chip that can also work on analogue. We know from experience that this is hopelessly unreliable, and a proper blanking chip should be installed. These dual-function chips do not work on PWM (Pulse Width Modulation) power supply systems, which remain popular on analogue layouts – not ours as yet; but we would like the choice, given the advantages that PWM has to offer!

In order to finance the purchase of the Y2K, we decided to part company with another train which seldom got used on the FLMJ and is even less likely to ‘fit in’ at the RTJ; the two X10 units (complete with the replacement chassis that was purchased quite recently). The purchaser is a Friend of the RTJ so maybe we will still see it in photo format in years to come.

Manufacturer News

Over the last few months, Jeco has been delivering their newer Rc2 versions, mostly with the ex-ÖBB lighting arrangement. One can only speculate how soon the Rc1 and Rc4 (both in orange) will also arrive.

Just as we were finalising this update, the PCX87 model of the modern Volvo V90 arrived into the shops. Quite recently, the Minichamps 850 arrived also, both sedan and estate.

Other News

Something to think about… After the X1 units were introduced, the X10 followed, and one of the improvements was a better cab, stronger to protect the driver in the event of a minor collision or level crossing strike. In September an even newer X40 unit hit a tractor’s trailer on a crossing, and as the published image shews, the driver didn’t get much protection (the driver had left his seat in the last moment and was behind the bulkhead at the point of impact). The cab is made from fibreglass as it is an easy material to work with to make the trains look trendy (something that the X40 doesn’t quite achieve anyway). But it seems that the industry needs to reconsider its priorities.

Behind the Scenes

Mini-Series about the new railway; 11: Making it all work

The FLMJ had a simple analogue electrical system, and this is planned for the RTJ and all of the ‘attachments’ to it. Each track section had a two-way, centre-off (DTCO) switch. Switched one way, the track was connected to the local controller; switched the other way, the track was connected to a remote controller (from another station, for example), and there was a rotary switch to select between different remote controllers.

This principle worked well, but it is possible that it can now be made even easier. There were vague thoughts about how the FLMJ’s switching could be made easier, and as we prepare the RTJ, these thoughts can be put into practice. Each section within any location (through tracks and sidings at a station, for example) could have an on-on switch, and the DTCO switch. The first of these would determine if the track is switched to the local controller directly, or to the DTCO switch. The DTCO would then select station throat at one end or at the other end (or off). (If the station throat serves two lines, as a junction for example, then the position of the points would determine which ‘line’ is connected.)

Going to a much more intense level, we have often played with the idea of latching sections with relays (solid-state to keep the cost down). The thought is that a controller is selected by push-button on the track diagram, and a relay latches that section on. Using the polarity in the track, the next section then connects to the same controller, and as the train passes certain predetermined locations, the sections ‘to the rear’ disconnect and become available to the next train. (To some extent, the correct use of signals can assist with track selecting.)

We are also developing a train detection system for analogue, which in its simplest form uses electronic treadles at key locations, but in its more advanced form can use axle counters. (Being analogue, we can use the track polarity to determine the direction of travel!) This can be used in conjunction with signalling and interlocking; but it’s still under development so no more ought to be said at this stage!

In all cases, we are able to keep the control system easy to create and to use. (This is what DCC was supposed to achieve, but in practice we have observed people struggling to make it work and layouts coming to a complete standstill; not exactly conducive to an enjoyable hobby!) The purpose of simple cabling and switching with Analogue is that it is easy to install, easy to trace, easy to fix. It just needs a very basic understanding in natural logic. And each step forward in creating something like this, or modifying it, or repairing it, gives a great sense of satisfaction and achievement that is not available with DCC.

Next Month: Taking Stock.